Tuesday, 8 January 2013

Types of oscillators



http://www.ehow.com/list_6025253_oscillator-types.html


Oscillator Types

An oscillator is an electronic circuit that creates an alternating current signal. There are several different designs of oscillators that use inductors and capacitors. These circuit elements form tuned circuits that alternately shift energy between their magnetic and electric fields. Some oscillators use quartz crystals that oscillate with the repeated transfer between electrical and mechanical energy.



Oscillator Types thumbnail

An oscillator is an electronic circuit that creates an alternating current signal
  1. Tuned Circuit Oscillators

    • The most common designs employ inductors and capacitors in various configurations to form positive feedback in active components. Hartley oscillators use a tuned circuit consisting of a capacitor and two inductors connected in series. At the critical frequency, the feedback is positive and the circuit oscillates. The variable capacitor may be used to allow for adjustment of the oscillator frequency. Similar to the Hartley design is the Colpitts oscillator that uses a feedback circuit made up of a single inductor and two capacitors.
      Colpitts oscillators that use series-tuned circuits instead of parallel ones for their feedback are called Clapp oscillators. This design allows for a large amount of inductance relative to the capacitance. This gives the tuned circuit a very high frequency selectivity (known as the "Q" factor) which reduces the tendency for the oscillator frequency to drift. The oscillator is inherently more stable because stray inductances are so much smaller than the inductor in the circuit, and therefore have less of an impact on the frequency.

    Crystal Oscillators

    • Crystal oscillators (known as XOs) depend on a piezoelectric quartz crystal for their resonance, which determines the frequency at which they oscillate. Crystals are specially cut with precise dimensions so they will oscillate at specific frequencies. Because of the superior frequency selectivity of the crystal, the oscillator frequency is extremely stable and accurate. Crystal oscillators are used for electronic clocks and in other applications where extreme accuracy is needed. They are not only more accurate than circuits using inductive and capacitive circuits, they oscillate at much higher frequencies than can be reliably achieved with the tuned circuit design.
      For even greater stability the crystal may be contained in a heated casing called an oven to keep it at a constant temperature to remove temperature drift. Such a device is known as a temperature-controlled crystal oscillator (TCXO).

    VCOs

    • Voltage Controlled Oscillators (VCOs) are made with a circuit element that changes its characteristics in response to an applied voltage. In this way the frequency of the oscillator can be manually or automatically controlled. The tuning element is usually a varactor diode whose capacitance varies with the voltage that is applied to it.

    Drift Control

    • To improve the stability of an oscillator, additional circuitry is sometimes incorporated to offset errors. The output frequency may be monitored and controlled automatically to hold the frequency to an assigned value. The most common method employed for this function is the phase lock loop. Other circuit elements that react to temperature changes may provide compensation to keep the frequency more constant.




http://chettinadtech.ac.in/wr/materials/UG/Engineering/First%20year/SECOND%20SEM/COMMON/electronics/3rd%20unit%20%20ece%20ed%20p2%20.pdf


 Types of oscillators

An electronic oscillator is an electronic circuit that produces a repetitive electronic
signal, often a sine wave or a square wave.

A low-frequency oscillator (LFO) is an electronic oscillator that generates an AC
waveform between 0.1 Hz and 10 Hz. This term is typically used in the field of audio
synthesizers, to distinguish it from an audio frequency oscillator.

Types of electronic oscillator
There are two main types of electronic oscillator: the harmonic oscillator and the
relaxation oscillator.
Harmonic oscillator

The harmonic oscillator produces a sinusoidal output. The basic form of a harmonic
oscillator is an electronic amplifier with the output attached to a narrow-band electronic
filter, and the output of the filter attached to the input of the amplifier. When the power
supply to the amplifier is first switched on, the amplifier's output consists only of noise.
The noise travels around the loop, being filtered and re-amplified until it increasingly
resembles the desired signal.
A piezoelectric crystal (commonly quartz) may be coupled to the filter to stabilise the
frequency of oscillation, resulting in a crystal oscillator.
There are many ways to implement harmonic oscillators, because there are different ways
to amplify and filter. For example:
• Armstrong oscillator
• Hartley oscillator
• Colpitts oscillator
• Clapp oscillator
• Pierce oscillator (crystal)
• Phase-shift oscillator
• RC oscillator (Wien Bridge and "Twin-T")
• cross-coupled LC oscillator
• Vačkář oscillator  Relaxation oscillator


The relaxation oscillator is often used to produce a non-sinusoidal output, such as a
square wave or sawtooth. The oscillator contains a nonlinear component such as a
transistor that periodically discharges the energy stored in a capacitor or inductor, causing
abrupt changes in the output waveform.
Square-wave relaxation oscillators can be used to provide the clock signal for sequential
logic circuits such as timers and counters, although crystal oscillators are often preferred
for their greater stability.
Triangle-wave or sawtooth oscillators are used in the timebase circuits that generate the
horizontal deflection signals for cathode ray tubes in analogue oscilloscopes and
television sets. In function generators, this triangle wave mays then be further shaped into
a close approximation of a sine wave.
Other types of relaxation oscillators include the multivibrator and the rotary traveling
wave oscillator

WAVE GENERATORS play a prominent role in the field of electronics. They
generate signals from a few hertz to several gigahertz (10
9
 hertz).
Modern wave generators use many different circuits and generate such
outputs as SINUSOIDAL, SQUARE, RECTANGULAR, SAWTOOTH, and TRAPEZOIDAL
waveshapes. These waveshapes serve many useful purposes in the
electronic circuits you will be studying. For example, they are used
extensively throughout the television receiver to reproduce both
picture and sound.
One type of wave generator is known as an OSCILLATOR. An oscillator can
be regarded as an amplifier which provides its own input signal.
Oscillators are classified according to the waveshapes they produce and
the requirements needed for them to produce oscillations.


CLASSIFICATION OF OSCILLATORS (GENERATORS)  
Wave generators can be classified into two broad categories according
to their output waveshapes, SINUSOIDAL and NONSINUSOIDAL.
Sinusoidal Oscillators
A sinusoidal oscillator produces a sine-wave output signal. Ideally,
the output signal is of constant amplitude with no variation in
frequency. Actually, something less than this is usually obtained. The
degree to which the ideal is approached depends upon such factors as
class of amplifier operation, amplifier characteristics, frequency
stability, and amplitude stability.  Sine-wave generators produce signals ranging from low audio frequencies
to ultrahigh radio and microwave frequencies. Many low-frequency
generators use resistors and capacitors to form their frequencydetermining networks and are referred to as RC OSCILLATORS. They are
widely used in the audio-frequency range.
Another type of sine-wave generator uses inductors and capacitors for
its frequency-determining network. This type is known as the LC
OSCILLATOR. LC oscillators, which use tank circuits, are commonly used
for the higher radio frequencies. They are not suitable for use as
extremely low-frequency oscillators because the inductors and
capacitors would be large in size, heavy, and costly to manufacture.
A third type of sine-wave generator is the CRYSTAL-CONTROLLED
OSCILLATOR.
The crystal-controlled oscillator provides excellent frequency
stability and is used from the middle of the audio range through the
radio frequency range.

RC Phase Shift Oscillator
An oscillator is a circuit, which generates ac output signal without giving any input ac
signal. This circuit is usually applied for audio frequencies only. The basic requirement
for an oscillator is positive feedback. The operation of the RC Phase Shift Oscillator can
be explained as follows. The starting voltage is provided by noise, which is produced due
to random motion of electrons in resistors used in the circuit. The noise voltage contains
almost all the sinusoidal frequencies. This low amplitude noise voltage gets amplified
and appears at the output terminals. The amplified noise drives the feedback network
which is the phase shift network. Because of this the feedback voltage is maximum at a
particular frequency, which in turn represents the frequency of oscillation. Furthermore,
the phase shift required for positive feedback is correct at this frequency only. The
voltage gain of the amplifier with positive feedback is given by  From the above equation we can see that if  . The gain becomes infinity
means that there is output without any input. i.e. the amplifier becomes an oscillator. This
condition  is known as the Barkhausen criterion of oscillation. Thus the output
contains only a single sinusoidal frequency. In the beginning, as the oscillator is switched
on, the loop gain Aβ is greater than unity. The oscillations build up. Once a suitable level
is reached the gain of the amplifier decreases, and the value of the loop gain decreases to
unity. So the constant level oscillations are maintained. Satisfying the above conditions of
oscillation the value of R and C for the phase shift network is selected such that each RC
combination produces a phase shift of 60°. Thus the total phase shift produced by the
three RC networks is 180°. Therefore at the specific frequency fo the total phase shift
from the base of the transistor around the circuit and back to the base is 360° thereby
satisfying Barkhausen criterion. We select R1=R2=R3∗=R and C1=C2=C3=C
The frequency of oscillation of RC Phase Shift Oscillator is given by  At this frequency, the feedback factor of the network is  . In order that  it
is required that the amplifier gain  for oscillator operation
OSCILLATORS

What are oscillator basics? 
Some people regard the design of RF Oscillators and oscillator basics in particular, to be
something akin to a "black art" and after many years of swearing at "cranky" oscillators
I'm not all too sure they are all that wrong. I suggest you ensure you remember this old
saying:
"Amplifiers oscillate and oscillators amplify" - unknown
Introduction to oscillator basics
When I was a kid, yes I can remember back to the late 1940's, we collected all manner of
junk. Cool was anything remotely electrical and, of course bicycle dynamos, lamps or
motors were even "extra cool".
We as precious little seven year olds conceived - all budding nuclear physicists that we
were - of this real smart idea, obviously nobody had ever thought of this before.
"Why don't we connect a motor to a generator, so the motor drives the generator,
providing electricity for the motor, which continues to drive the generator and it'll go on,
and on, and on for a hundred years and we'll become rich and world famous!"
Of course we had no concept of frictional losses (I think that's right) way back then. Nor
had the words "perpetual motion" passed our ears.
The whole point of that little story is to crudely demonstrate the principle of how an
oscillator works. If you can follow that childishly naive concept then you will kill them in
this.

Principles of Oscillator operation 
Every oscillator has at least one active device (smarties don't complicate matters for me -
just read on) be it a transistor or even the old valve. This active device and, for this
tutorial we'll stick to the humble transistor, acts as an amplifier. There is nothing flash about that. For this first part of the discussion we will confine ourselves to LC Oscillators
or oscillator basics and I'll keep the maths to an absolute minimum.
At turn on, when power is first applied, random noise is generated within our active
device and then amplified. This noise is fed back positively through frequency selective
circuits to the input where it is amplified again and so on, a bit like my childhood project.
Ultimately a state of equilibrium is reached where the losses in the circuit are made good
by consuming power from the power supply and the frequency of oscillation is
determined by the external components, be they inductors and capacitors (L.C.) or a
crystal. The amount of positive feedback to sustain oscillation is also determined by
external components.
Hartley Oscillator 
I decided to use the Hartley Oscillator for the simple reason it's my favourite. Recently it
was discussed that your favourite oscillator was likely the one which worked best for you
and I think that is quite true. So here it is in it's most simplified form.
Figure 1 - schematic of a hartley oscillator
Colpitts Oscillator 
The basic Colpitts oscillator circuit look like this and you will see some similarities.
Figure 2 - schematic of a collpitts oscillator If you consider positive feedback is applied to compensate for the losses in the tuned
circuit, the amplifier and feedback circuit create a negative resistor. When Z1 and Z2 are
capacitive, the impedance across the capacitors can be estimated from a formula I won't
lay on you here because it includesbeta, hie, as well as XC1 and XC2. Suffice to sayit can
be shown that the input impedance is a negative resistor in series with C1 and C2.  And
the frequency is in accordance with:


Frequency or Phase Stability of an Oscillator 
Frequency or phase stability of an oscillator is customarily considered in the long term
stability case where frequency changes are measured over minutes, hours, days even
years. Of interest here are the effects of the components changes, with ambient
conditions, on the frequency of oscillation. These might be caused by changes in the
input voltage, variations in temperature, humidity and ageing of our components.
Never underestimate the effects of these variations on the frequency of operation. I've
gone nuts working on so called precision designs, with precision components, where the
frequency wandered at random over several kilohertz over several minutes. Needless to
say I'd "messed up".
Short term stability is also of great interest and, again I could lay some real heavy maths
on you but I won't. I'll simply say it can be mathematically proven that the higher the
circuit Q, the higher this stability factor becomes. The higher the circuit Q, the better the
ability the tuned circuit can filter out undesired harmonics AND noise.
Reducing Phase Noise in Oscillators
1. Maximize the Qu of the resonator.
2. Maximize reactive energy by means of a high RF voltage across the resonator. Use a
low LC ratio.
3. Avoid device saturation and try to use anti parallel (back to back) tuning diodes.
4. Choose your active device with the lowest NF (noise figure).
5. Choose a device with low flicker noise, this can be reduced by RF feedback. A bipolar
transistor with an unby-passed emitter resistor of 10 to 30 ohms can improve flicker noise
by as much as 40 dB. - see emitter degeneration  6. The output circuits should be isolated from the oscillator circuit and take as little power
as possible.
Effects of ambient changes on stability in oscillators
A frequency change of a few tens of hertz back and forth over a couple of minutes would
mean nothing to an entertainment receiver designed for the FM Radio band. Such a drift
in an otherwise contest grade receiver designed to receive CW (morse code) would be
intolerable. It's a question of relativity.
Minimizing Frequency drift in oscillators
These are random and not in any particular order.
1. Isolate the oscillator from succeeding stages with a well designed buffer stage followed
by a stage of amplification. Large signals can often then be reduced by a 3 or 6 dB
attenuator which also has the benefit of presenting a well defined load impedance to the
amplifier. If the stage is feeding a mixer, as is most often the case, then another benefit is
the mixer (you are using double balanced mixers?), also see a source impedance of 50
ohms.
2. Ensure the mechanical stability of your oscillator is such that mechanical vibration can
have no effect on components, especially those frequency determining components.
3. Supply the oscillator with a clean well regulated supply. If using varactor tuning,
doubly ensure the tuning DC voltage is as clean as possible, a few hundred micro volts of
noise can be imposed on the oscillator signal. Use back to back diodes for the variable
element. Air variables are hard to come by although they offer far superior Q figures. DC
tuning tends to be more versatile.
4. Minimize circuit changes from ambient variations by using NPO capacitors,
polystyrene are dearer but excellent, silvered mica in my opinion are not what many
people believe and are highly over rated.
5. The inductor should be air wound on a coil form with a configuration to maximize Qu.
If you must use a toroid, where possible try to use the 6 type as it offers the best Q.
Sometimes, for other reasons you might have to use a slug tuned form.
6. Parallel a number of smaller value NPO capacitors rather than using one large one in
frequency determining components. For trimmers try and use an air variable. Keep an eye
out for small value N750, N1500 capacitors, < 15 pF, when available and are found to be
dirt cheap. These are sometimes useful in taming drift in an oscillator.
7. Bipolar or FETS for active device seems to be a matter of personal preference and I've
seen some ferocious arguments over that one. Consensus seems to come down in favour
of FETS. Me, I'm a bipolar man because FETS hate me pure and simple.  UJT Relaxation Oscillator
The negative resistance characteristic of the unijunction
transistor makes possible its use as an oscillator.
Relaxation Oscillator Concept 
The concept of a relaxation oscillator is illustrated by this flasher circuit where a battery
repeatedly charges a capacitor to the firing threshold of a bulb, so that the bulb flashes at
a steady rate.
A relaxation oscillator is a repeating circuit (like the flasher circuit illustrated above)
which achieves its repetitive behavior from the charging of a capacitor to some event
threshold. The event discharges the capacitor, and its recharge time determines the repetition time of the events. In the simple flasher circuit, a battery charges the capacitor
through a resistor, so that the values of the resistor and the capacitor (time constant)
determine the flashing rate. The flashing rate can be increased by decreasing the value of
the resistance.
One of the reasons for the importance of the relaxation oscillator concept is that some
neural systems act like relaxation oscillators. For example, the bundle of nerve fibers
called the SA node (sino-atrial node) in the upper right hand part of the heart acts as the
natural pacemaker of the heart, firing at a regular rate. The rate of this relaxation
oscillator is variable, and can be increased in response to exertion or alarm. Other nerve
cells recharge like a capacitor, but then wait for some kind of stimulus to fire. In response
to some kind of trauma, it might be that the firing threshold is lowered enough to "self
fire" and act as a relaxation oscillator. This is an intriquing possibility for explaining the
ringing in the ears after a loud concert.

No comments:

Post a Comment